WEBVTT

00:00:00.000 --> 00:00:01.166
(transition thuds)

00:00:01.166 --> 00:00:02.152
(logo dings)

00:00:02.166 --> 00:00:06.041
The Motion Sensor Gen 2 is
always on the lookout for uninvited guests

00:00:06.041 --> 00:00:07.500
when your system is armed.

00:00:07.583 --> 00:00:10.000
It can detect motion within 35 feet,

00:00:10.291 --> 00:00:12.333
with a 90 degree field of view.

00:00:12.416 --> 00:00:15.125
The Motion Sensor Gen 2
also has Pet Mode

00:00:15.125 --> 00:00:17.291
to distinguish between people and pets.

00:00:17.708 --> 00:00:18.833
Before getting started,

00:00:19.000 --> 00:00:21.958
you'll need to make sure you have a
Gen 3 SimpliSafe system

00:00:21.958 --> 00:00:24.291
that's running the latest firmware version.

00:00:24.291 --> 00:00:28.000
You can check for firmware updates
using the SimpliSafe Mobile App.

00:00:28.083 --> 00:00:31.916
We recommend placing the Motion Sensor
Gen 2 in the corner of a room,

00:00:32.083 --> 00:00:35.458
in an area where an intruder
is most likely to pass through.

00:00:35.541 --> 00:00:39.000
You'll want to mount it at six feet off
the ground for best results.

00:00:39.083 --> 00:00:41.625
Avoid placing the Motion Sensor
near a heater,

00:00:41.625 --> 00:00:44.625
air conditioner, lamp or direct sunlight.

00:00:44.666 --> 00:00:46.833
Changes in heat signatures within a room

00:00:46.833 --> 00:00:49.375
have the potential to trigger false alarms.

00:00:49.833 --> 00:00:51.375
Let's get started.

00:00:51.375 --> 00:00:54.250
To add the Motion Sensor Gen 2
to your system,

00:00:54.291 --> 00:00:58.208
open the SimpliSafe
Mobile App on your phone or tablet.

00:00:58.291 --> 00:01:02.125
Navigate to the three bar menu
in the upper left corner of the screen,

00:01:02.125 --> 00:01:05.250
then select add device or camera.

00:01:05.333 --> 00:01:08.541
Choose Motion Sensor
from the list of available products,

00:01:08.625 --> 00:01:12.458
then follow the in-app prompts
to complete the setup.

00:01:17.083 --> 00:01:18.916
If you have pets within your home,

00:01:18.916 --> 00:01:22.958
you'll want to make sure that you enable
pet mode during the installation process.

00:01:23.041 --> 00:01:26.500
Pet mode allows your cats or dogs to roam
freely around your home

00:01:26.500 --> 00:01:28.250
without triggering the alarm,

00:01:28.250 --> 00:01:31.083
so long as they're under 60 pounds.

00:01:31.166 --> 00:01:34.541
Now it's time to physically
install your Motion Sensor.

00:01:34.625 --> 00:01:37.583
If you're mounting the Motion Sensor
using adhesive,

00:01:37.583 --> 00:01:41.083
first, clean the surface with an
alcohol-based cleaning solution,

00:01:41.333 --> 00:01:43.750
allowing time for the surface to dry.

00:01:43.791 --> 00:01:48.125
Once dry, peel back the cover
of the adhesive on the back of the sensor.

00:01:48.208 --> 00:01:52.583
Press and hold the sensor in place
for 30 seconds to adhere it to the wall.

00:01:52.666 --> 00:01:54.416
If you’re screw mounting your sensor,

00:01:54.416 --> 00:01:56.916
remove the mounting plate
from the back of the sensor

00:01:56.916 --> 00:02:01.333
by sliding the front part of the sensor up
and off the bracket with light force.

00:02:01.416 --> 00:02:04.500
You'll need to run the screw
through the adhesive backing.

00:02:04.708 --> 00:02:08.291
Once mounted, slide the motion sensor back
on to the mounting plate

00:02:08.291 --> 00:02:09.791
until it clicks into place.

00:02:09.791 --> 00:02:10.208
(click)

00:02:10.250 --> 00:02:11.208
That's it.

00:02:11.208 --> 00:02:15.541
Your Motion Sensor Gen 2 is now
set up and ready to protect your home.

00:02:15.625 --> 00:02:17.791
To customize your sensor settings,

00:02:17.791 --> 00:02:19.958
or to learn more about
preventing false alarms,

00:02:20.125 --> 00:02:23.208
visit us at support.simplisafe.com.

00:02:27.125 --> 00:02:28.291
(transition thuds)

00:02:28.291 --> 00:02:29.291
(logo dings)